Show Tips
Sorted by relevance | Sort by date
Found 590 matching posts for Olympus in Micro-Manager Showing posts 1 to 12.
Dear all, I tried to use the Olympus DP72 camera with micromanager 1.3 and 1.4 with no success. Are there any solutions ? The camera is connected to a PCI-card and is used on an Olympus BX51 equipped with a Ludl stage. Thank you. With Kind Regards, Christian Dr.rer.physiol. Christian...
in Micro-Manager by Herr, Christian Dr. — 3 replies in thread
Does anyone know if and when will MM support the new Olympus ix83? David David Sprinzak Department of Biochemistry and Molecular Biology The George S. Wise Faculty of Life Sciences Tel Aviv University Tel Aviv 69978 Israel Phones: +972-3-6405218 (office) +972-3...
in Micro-Manager by David Sprinzak — 2 replies in thread
Hi, I am thinking of buying an Olympus camera for my microscope possibly the DP22/27 or the SC50/100. Does anyone know if these cameras are compatible with micromanager? Cheers Chris Sent from my iPhone...
in Micro-Manager by chris jones — 1 replies in thread
Hi all, I found a problem with the Olympus Hub IX2-UCB. If there is no additional plugin card present in the hub (e.g. a Z-Fokus card) it's not possible to add the hub to the devices list. The explicit problem is that the IX2-UCB does not answer to the "2Unit?" command. I attached a...
in Micro-Manager by Korbinian Kapsner — 6 replies in thread
Hi, I need to know to connect my olympus UC30 to micromanager through an olympus IX51 microscope. Thanks. ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http...
in Micro-Manager by Jennifer Kee — 1 replies in thread
Hi all, Is this possible to use MM with Olympus STC controller and Maerzhaeuser XY-stage? It is connected to Olympus serial port of the Olympus real-time controller board, but I can connect this controller through the rs232. Is this controller compatible with Corvus controller? I have also problems with configure Olympus MT20 illumination source. Thanks, Sebastian
in Micro-Manager by sstudent — 1 replies in thread
Dear Jennifer “Hi, I need to know to connect my olympus UC30 to micromanager through an olympus IX51 microscope. Thanks.” I remember the same question was asked ~2 years ago; I thought the Ximea drivers might be an option, but I’m not sure if it could be tested then: http://micro-manager...
in Micro-Manager by m.losen — 1 replies in thread
...:04.158399 tid1632 [IFO,Core] Will initialize device Olympus IX83 2015-10-14T19:29:06.923557 tid1632 [dbg,dev:Olympus IX83] --> 0:L 1,1 Per these threads http://micro-manager.3463995.n2.nabble.com/Olympus-IX83-with-Hamamatsu-ORCA-D2-td7581669.html http://sourceforge.net/p/micro-manager/mailman...
in Micro-Manager by EricG — 0 replies in thread
Hi, I am trying to get micro-manager to work with our Olympus IX81 microscope, but I am having some difficulty with configuring our camera. It's an Olympus XM10 . I cannot find any support for this device, nor does the OpenCV or Twain seem to work. Can anyone help? Thanks, Daniel
in Micro-Manager by daniel — 2 replies in thread
Thank you for the response. Do you know of a good autofocus tool that can be used with multi-well, ie fast and reliable? I have contacted my olympus rep and am awaiting a response.
in Micro-Manager by jcompton — 9 replies in thread
Dear Arthur, Have your tried ZDC2? Is there any how-to on wiki about how to setup the ZDC for a Olympus scope? In this webpage http://valelab.ucsf.edu/~MM/MMwiki/index.php/Olympus , it mentions "there are two modes of Control: Computer and Manual + Computer". I am wondering how to setup the second mode. Thank you very much for your time. Sincerely, Liang
in Micro-Manager by cail — 9 replies in thread
On Wed, Jan 16, 2013 at 3:13 AM, akerimcapar <akerimcapar@...> wrote: > I am trying to connect to an Olympus Hub (Model U-CBM) with MM. I am using > Hama Null-Modem RS232 Cable. My operating system is WinXP-32 Bit. I am > getting the following error: "Error in device OlympusHub: Error Code...
in Micro-Manager by Pariksheet Nanda — 1 replies in thread
Next 12 »
Show Tips